QT® Carts

Quick Start Guide

Set-Up & Use

Unpack Your New QT Cart

All QT® Carts go through a 12-Step Quality Check process before shipping. Upon arrival, please unpack your new QT® Cart.

Unlock Your New QT Cart

Depending on the models purchased, you will either have a Key Lock, eLock, or Prox Lock. This determines how you access your unit.

Clean Your New QT Cart

Follow the recommended cleaning instructions outlined below and in your Use & Care Guide for proper maintenance of your QT® Cart.

Unpack Your New QT® Carts

Inspection:

  • Receiving area must meet all State and Local regulations prior to unpacking 
  • Customer must inspect both the skid and Cart before and after unpacking to determine if any items were damaged during shipping 
  • All damaged items must be listed on the Bill of Lading 
  • Customer is responsible for the proper disposal of all packing materials; the disposal of these items must meet all State and Local regulations 

Unpacking QT® Carts

QT Carts are shipped on well-constructed wooden skids. Care must be taken while unpacking the items to avoid damage. Retain all shipping materials until the items are completely unpacked and inspected for damage. 

remove box from QT Cart

1. Lifting from the top, pull the box cover off the QT Cart.  Several Styrofoam pieces will fall off to the sides.

Remove Plastic Cover QT Cart

2. Remove the plastic cover over the QT Cart.     

NOTE:  Set packing materials to the side until you are able to test the product to ensure it is working properly. 

Two People lift QT Cart

3. With two people, one person on either side of the cart, lift the cart from out of the bottom portion of the box, and place it on the ground. 

Two People Lift Cart

NOTE:  Lift the cart out of the box by grabbing and lifting the QT Cart from the bottom, as shown.

Remove Tape from QT Cart

4. On the right side of the QT Cart, remove the tape strips from over the pull-out shelf. 

Keys taped to slide out

NOTE: The keys are in a small bag, taped to the shelf. Store the Keys and the Manuals with a green sticker in a safe place.

Divider Sets for QT Carts

5. Divider Sets can be found in the third drawer down.  

If You Have Key Lock, Stop Here. If You Have eLock, Continue to Unlocking Your New QT® Cart

Key Lock

Logicell Locked Unlocked

eLock

Unlock Your New QT® Carts

1. Initial eLock Programming 

Your QT Cart is set to default Supervisor and User Codes. These default codes should be changed before using your QT Cart. Best practices for Supervisor/User Codes are to have the Supervisor Code be at least one digit longer than a User Code. 

DEFAULT CODES ARE: 

Supervisor – 12345
User – 1234 

NOTE: You cannot delete the Default Supervisor Code until a new Supervisor Code is created. 

2. Add a NEW SUPERVISOR CODE 

If the Green Light is Blinking Press LOCK/CLEAR. If it is not, move to next step
Enter Default Supervisor Code 12345 and hit ENTER.  The cart will Unlock
Press ADD SUPERVISOR
Enter NEW Supervisor Code (4 to 14 digits)
Press ENTER or scan Supervisor Card credential (if equipped with Proximity Lock)
NOTE: This Supervisor Code now occupies slot 1
Press LOCK/CLEAR to exit 

3. Remove Default Supervisor Code 

Enter Your NEW Supervisor Code and press ENTER or scan valid Supervisor Card credential (if equipped with Proximity Lock)
• Press and Hold ADD SUPERVISOR if the credential to be deleted is a Supervisor
• Press LOCK/CLEAR. The lights on the keypad will blink from right  to left
Release ADD SUPERVISOR
• Enter the PIN code to be deleted and press ENTER or present the card to be deleted
• Press LOCK/CLEAR 

NOTE:  You cannot login using the same Supervisor Code you are trying to Delete. For example, if you are trying to Delete Supervisor Code 12345, you must be logged into the system with a different Supervisor Code.

4. Add New User Code 

Enter valid Supervisor Code and press ENTER or scan valid Supervisor Card credential (if equipped with Proximity Lock) 2. Press ADD USER
• Enter the new User Code (4 to 14 digits) or scan new User Card credential
• Press ENTER
• Press LOCK/CLEAR
• Test new User Code 

5. Delete Default User Code 

Enter valid Supervisor Code and press ENTER or scan valid Supervisor Card credential (if equipped with Proximity Lock)
Press and Hold ADD USER if the credential to be deleted is a User
Press LOCK/CLEAR. The lights on the keypad will blink from right to left
Release ADD USER
Enter the Default User Code and press ENTER or scan the User Card credential to be deleted
Press LOCK/CLEAR 

6. Set up Dividers and go

Clean Your New QT® Carts

WARNING

  • Always comply with facility cleaning standards and guidelines*.
  • Before using any cleaner, do a spot test on a small, inconspicuous area of your product to ensure it will not cause damage to the finish.
  • Solvents, acidic or abrasive cleaners can damage surfaces and are not recommended.
  • Wipe spill away promptly and rinse several times with water.
  • Steel wool and other abrasive cleaning pads will damage the surface.
  • Do not mix different cleaning agents to clean or disinfect.
  • Rust remover, drain cleaners and toilet bowl cleaners contain harsh chemicals and will quickly cause permanent damage.
  • Hair, textile and food dyes can cause permanent stains.

Recommended Cleaning Products

Soap and water and most common cleaners/disinfectants are excellent for most cleaning and disinfecting purposes as long as the directions on the label are followed. 

The following cleaning products are acceptable when used according to directions: 

  • AHP Accel® TB 
  • Bleach Mixture (1/3 cup bleach per 1 gallon of water) 
  • Dispatch® Hospital Cleaner Disinfectant 
  • DiverseyTM Oxivir® Tb Wipes 
  • Hydrogen Peroxide 
  • Isopropyl Alcohol 
  • MetrexTM CaviWipesTM 
  • Oxivir® Tb 
  • Quaternary Cleaners 
  • Sani-Cloth® AF3 
  • Sani-Cloth® HB 
  • SanimasterTM 6 
  • Super Sani-Cloth® 

NOTE: DO NOT use any of the above listed cleaners on the keyboard. Only non-acid based cleaners.

Recommended Cleaning Procedures

  1. Remove debris before application of the cleaner/disinfectant.
  2. Apply cleaner/disinfectant according to the label. Avoid using sprays on products with electronic components.
  3. Ensure that the solution is wiped away with a clean cloth. Do not allow the cleaner to remain on product longer that the time recommended on the label.
  4. When solutions are NOT contained in a spray bottle make sure to appropriately dispose of the solution, cleaning cloth and cleaning supplies after each cleaning.

Keypad Cleaning Instructions

1.To clean the Keypad surface, apply non-acid based cleaner to a clean cotton cloth. DO NOT spray cleaner directly on the Keypad.

2. Wipe down Keypad (especially the edges) and ensure excess cleaner is removed.

THE USE OF EXCESSIVE CLEANER WILL CAUSE THE CIRCUITRY TO CORRODE AND FAIL.

For troubleshooting, help, and FAQs for Medical Storage Carts, CLICK BELOW.

For helpful, how-to videos for Medical Storage Carts,
CLICK BELOW.

QT® Cart Accessories

Logicell Supply Cart
Catheter Slides Feature

1. Silent, Hospital Grade Casters

Wire Baskets with Divi Feature

2. Soft Return Drawers

Catheter Slides Feature

3. Accessory Rail

Clear Tubs with Divider Feature

4. Large Capacity Drawers

145-24 Lockable Drawer Feature

eLock System (not shown)

145-24 Lockable Drawer Feature

Slide Out Shelf (not shown)

Learn More

Learn more by calling (800) 665-3760 or by clicking on the link below.